●Abrasion and impact resistance
●Seamless, easy to clean, microorganisms are not easy to survive
●Strong adhesion, high toughness
| color | transparent |
| Mixing ratio | — |
| solid,% | 40±2 |
| Painting times | 1 time |
| Dry film thickness, um | 20~30 |
| Coating rate | Dosage: 0.12~0.15kg/m2 |
| Actual value: It is related to many factors such as surface treatment, external environment, construction method, etc. | |
| Main technical indicators (implementing GB/T22374-2008 floor coating material surface coating standard) |
| Serial number | Test items | Technical indicators | Measured | Testing standards | |
| 1 | Color and appearance | Consistent color, smooth and even | qualified | Visual inspection | |
| 2 | Drying time, h | Touch Dry | ≤4 | 3 | GB/T 1728-1989 |
| Get down to business | ≤24 | 12 | |||
| 3 | Adhesion, Grade | ≤1 | 0 | GB/T 9286-1998 | |
| 4 | Flexibility, mm | 1 Pass | 1 | GB/T1731-1993 | |
| 5 | Hardness (pencil hardness) | ≥2 hours | 6 | GB/T6739-1996 | |
| 6 | Impact resistance (50cm.kg) | 50 Pass | 50 | GB/T1732-1993 | |
| 7 | Abrasion resistance (750g/500r) | ≤0.030 | 0.03 | GB/T1768 | |
| 8 | Water resistance (48h) | The paint film is complete, does not bubble or peel off, slight discoloration is allowed, and can be restored within 2 hours | qualified | GB/T1733-1993 | |
| 9 | Resistant to 20% NaOH, 72h | The paint film is complete, without blistering or peeling, and slight discoloration is allowed | qualified | GB/T 9274-1988 | |
| 10 | Resistant to 10% H 2 SO 4 ,48h | No bubbling, no shedding, slight discoloration allowed | qualified | GB/T9274-1988 | |
| 11 | Oil resistance (120# gasoline), 72h | No bubbling, no shedding, slight discoloration allowed | qualified | GB/T1724-1933 | |
● Old floors with paint
Completely grind away loose or incompatible old coatings to expose the concrete surface. Clean, dry and intact compatible coatings do not need to be removed.
● Oily floors
Oil stains will seriously affect the adhesion of floor coatings to the base surface. Oily floors must be completely cleaned and polished.
● New concrete floors
Make sure the floor has exceeded the maintenance period and the moisture content of the floor is less than 6%. It is critical to use mobile sandblasting tools and grinding equipment to treat the concrete surface to achieve the correct surface roughness.
Painting environment humidity range: Relative humidity <85%
Ventilation conditions: Ensure that the construction site is ventilated and dust-free. However, there should be no strong wind to avoid bringing in dust and affecting the appearance.
4 hours after opening the can
● Construction method
| Airless spray, air spray, brush and roller | |
| Roller coating | Large area construction use |
| Spraying | Can be applied using conventional air spray or airless spray |
| Brush | It is recommended to use a soft-bristled brush for small areas. |
● Thinner —
● Drying time and coating interval
It is related to the temperature and humidity of the coating environment. Usually, the coating interval is 12 hours under standard conditions (25℃, relative humidity 60%)
● Coating matching
Applicable substrate Cement or concrete floor
Applicable coating Epoxy primer
Solvent-free polyurethane midcoat, epoxy midcoat
During transportation, the environment of the carriage should be dry and closed, the materials should be stacked stably, and the relevant regulations should be met.
● Avoid contact with skin and eyes.
● If paint comes into contact with skin, wash with warm water and/or an appropriate detergent. If paint comes into contact with eyes, rinse with plenty of water and seek medical attention immediately.
● Ensure good ventilation.
● Paint contains flammable substances. Please keep away from sparks and prohibit smoking in the vicinity.
● Comply with all health and safety regulations on site.